1mm Stainless Steel 300mm Pipe - 7 inch

APPLICATION
Suitable for gas, oil and solid fuel appliances with temperatures up to 750 degrees C.
1mm Stainless Steel Stove pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.
1mm Stainless Steel Stove Pipe should NOT be used to pass through ceilings or wall.

CONSTRUCTION
1mm Stainless Steel Stove Pipe is a single skin flue system manufactured in 316 grade stainless steel and is 1mm thick.
Suitable for gas, oil and solid fuel appliances with temperatures up to 750 degrees C

INSTALLATION
You should not install a piece of 1mm Stainless Steel Stove Pipe within 3 times the diameter of the flue from combustible material, e.g. wood, plaster boards, etc.
A 5 inch (125mm) diameter piece of 1mm Stainless Steel Stove Pipe should be 15 inches (375mm) away from combustible materials.
When installing make sure 1mm Stainless Steel Stove Pipe is installed the correct way up - the smaller convoluted diameter should always be pointing downward.
This is because all the condensates will stay within the flue system and not pass to the outside of Stove Pipe.
Each joint should be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.
Each part should then be secured by using a Joint Clamp Band.

MAINTENANCE
You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.
You can acheive this by installing a pipe with an access door.
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

5 inch Pellet Pipe - Tee F/F Black enamel finish

90 degree tee with two female ends, one to connect to the appliance and the other to connect to the next section of pipe. The one male end is used to connect the Tee Cap (sold seperately). You will need a tee cap with this item and also TWO gasket seals.

Flue Liner 904L/904L Grade Multifuel (904L/904L Grade)

APPLICATION
A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat, smokeless fuels.
If the appliance is mainly going to be used to burn wood, and the appliance is not DEFRA approved you should increase the diameter of the Flue Liner to 150mm (providing this will fit in the masonry chimney), as recommended by Building Regulations.

CONSTRUCTION
The flue liner has a smooth inner liner made from 904L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 904L stainless steel and is 0.12mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a quattrolock seal.

APPROVAL
Flue Liner is approved and listed by HETAS

INSTALLATION - CHECK LIST
1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

INSTALLATION
Flue Liner should always be fitted from the top.
Make sure the arrows are pointing upwards (gas flow).
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner, again making sure the arrows on the Flue Liner are pointing away from the Nose Cone in a upward direction so when the liner is installed the arrows will be pointing to the top of the chimney
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone.

MAINTENANCE
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Flue Liner Installation Kit 4 5 inch

APPLICATION
Use this pack when you want to remove the existing chimney pot - and then replace it when the flue liner is installed. You will probably need to install a cowl or terminal for your chimney to offer some weather and bird protection.

PACK CONTAINS
1 x Top Plate - Ø125mm
1 x Top Clamp - Ø125mm
1 x Top Insert - Ø125mm
1 x Nose Cone - Ø125mm
1 x Increasing Adaptor to Black Pipe or Single Wall Flue - Ø100mm SW to Ø125mm Flex
1 x Chimney Notice Plate

Quattro-PLUS Flue Liner 904L Grade - Solid Fuel 250mm (10 inch)

WARRANTY
904L Grade Flue Liner is warranted for 20 years (conditions apply)

APPLICATION
A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat, smokeless fuels.

CONSTRUCTION
The flue liner has a smooth inner liner made from 904L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 904L stainless steel and is 0.12mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a quattrolock seal.

APPROVAL
Flue Liner is approved and listed by HETAS

INSTALLATION - CHECK LIST
1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

INSTALLATION
Flue Liner should always be fitted from the top.
Make sure the arrows are pointing upwards (gas flow).
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner, again making sure the arrows on the Flue Liner are pointing away from the Nose Cone in a upward direction so when the liner is installed the arrows will be pointing to the top of the chimney
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone.

MAINTENANCE
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Gather Hood 300mm x 300mm Base

 

Gathers are used on open fires and baskets. The formed stainless steel gather is connected to the multi fuel liner in the chimney. The gather helps the flow of gases up the chimney, it also prevents the liner coming into contact with a fierce heat that can be produced.

Installation Kit 4 6 inch



Installation Pack No. 4, ALL YOU NEED IN ONE BOX FOR USE WITH 150mm diameter multifuel flex
 

APPLICATION
Use this pack when you want to remove the existing chimney pot - and then replace it when the flue liner is installed. You will probably need to install a cowl or terminal for your chimney to offer some weather and bird protection.

PACK CONTAINS
1 x Top Plate - Ø150mm
1 x Top Clamp - Ø150mm
1 x Top Insert - Ø150mm
1 x Nose Cone - Ø150mm
1 x Increasing Adaptor to Black Pipe or Single Wall Flue - Ø125mm SW to Ø150mm Flex
1 x Chimney Notice Plate