100mm (4 inch) - Flue Liner 316L/904L Grade Multifuel

The 100mm (4 inch) - Flue Liner 316L/904L Grade Multifuel :

904L/316L Grade Flue Liner is warranted for 10 years (conditions apply).

A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat, some smokeless fuels.

The flue liner has a smooth inner liner made from 904L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.12mm thick. The Flue Liner is constructed from two strips of steel and the seam is folded in three planes to give a triplelock seal.

100mm (4 inch) - Flue Liner 316L Grade Multifuel Liner

The 100mm (4 inch) - Flue Liner 316L Grade Multifuel Liner :

316L Grade Flue Liner is warranted for 10 years (conditions apply)

A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.12mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a quattrolock seal.

Joiner

The Joiner :

Allows the joining of two pieces of multi fuel liner (only to be used in none flueing applications).

Nose Cone

The Nose Cone :

APPLICATION

The nose cone helps prevent snagging of a flue liner against the side of the stack during installation.

INSTALLATION

Insert a draw cord or string (not supplied) into the hole of the nose cone. Secure with a knot. make sure the draw cord is long enough to reach to the bottom of the stack. Now tape or secure the nose cone to the flue liner end.

MAINTENANCE

It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Rain Cap

The Rain Cap :

APPLICATION

Provides rain protection at the top of the stack.

INSTALLATION

Terminal slides over the top of the liner and can be screwed into place with self tapping screws (not supplied) or alternatively can be cemented in to place at the top of the stack.

MAINTENANCE

It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Top clamp

The Top clamp :

APPLICATION

Used in conjunction with the Top Plate and Top Insert Sleeve, the Top Clamp supports the weight of the flue liner at the top of the stack.

CONSTRUCTION

The glavanised steel plate measure 15 inch square (375mm).

INSTALLATION

Place the Top Plate over the chimney recess at the top of the stack. The Flue Liner should protrude throught the Top Plate hole by approximately 100mm.

Insert the Top Insert Sleeve into the Flue Liner. Now place the Top Clamp over the Flue Liner and tighten the two nuts and bolts until the Flue Liner is secure againts Top Insert Sleeve. Now apply a suitable acid resistant cement as a seal and weather proof render. While this cement is wet secure the chimney pot to this cement.

MAINTENANCE

It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Top Plate

The Top Plate :

APPLICATION

Used in conjunction with the Top Clamp and Top Insert Sleeve, the Top Plate supports the weight of the flue liner at the top of the stack.

CONSTRUCTION

The glavanised steel plate measure 15 inch square (375mm).

INSTALLATION

Place the Top Plate over the chimney recess at the top of the stack. The Flue Liner should protrude throught the Top Plate hole by approximately 100mm.

Insert the Top Insert Sleeve into the Flue Liner. Now place the Top Clamp over the Flue Liner and tighten the two nuts and bolts until the Flue Liner is secure againts Top Insert Sleeve. Now apply a suitable acid resistant cement as a seal and weather proof render. While this cement is wet secure the chimney pot to this cement.

MAINTENANCE

It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Increasing Adapter 100 Rigid to 125 Flex

The Increasing Adapter 100 Rigid to 125 Flex :

APPLICATION

Connects 125mm (5 inch) Flue Liner to 100mm (4 inch) Black Pipe / Vitreous Enamel / 1mm Stainless / Single Wall flue at the bottom of the chimney stack.

HETAS recommend that if you are burning wood then you should increase the size of the flue liner by 25mm from the appliances spigot size.

This is due to the amount of condensates that can be produced from burning unseasoned wood.

CONSTRUCTION

Made from 316 grade stainless steel, it has integral drain hole to let the condensates flow back into the flue.

INSTALLATION

1.Connect the bottom of the Flue Liner to the adaptors twin wall section, using self tapping screws and seal with either Fire Cement or High Temperature Silicone Sealant.

You can now conect the adapter using Fire Cement or High Temperature Silicone Sealant to either your appliance (if the appliance is a solid fuel appliance then you must have a least 600mm of flue pipe before this connection) or Black Pipe / Vitreous Enamel / Single Wall Stove Pipe. If the gap is large between the adapter and the pipe you can seal using a combination of Fire Cement / Silicone and Fire Rope.

MAINTENANCE

It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Flue Adapter 100 Rigid to 100 Flex

The Flue Adapter 100 Rigid to 100 Flex :

APPLICATION

Connects 100mm (4 inch) Flue Liner to 100mm (4 inch) Black Pipe / Vitreous Enamel / 1mm Stainless / Single Wall flue at the bottom of the chimney stack.

CONSTRUCTION

Made from 316 grade stainless steel, it has integral drain hole to let the condensates flow back into the flue.

INSTALLATION

1.Connect the bottom of the Flue Liner to the adaptors twin wall section, using self tapping screws and seal with either Fire Cement or High Temperature Silicone Sealant.

You can now conect the adapter using Fire Cement or High Temperature Silicone Sealant to either your appliance (if the appliance is a solid fuel appliance then you must have a least 600mm of flue pipe before this connection) or Black Pipe / Vitreous Enamel / Single Wall Stove Pipe. If the gap is large between the adapter and the pipe you can seal using a combination of Fire Cement / Silicone and Fire Rope.

MAINTENANCE

It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

The Flue Liner 904L/904L Grade Multifuel (100mm / 4 inch)

The Flue Liner 904L/904L Grade Multifuel (100mm / 4 inch) :

WARRANTY

904L Grade Flue Liner is warranted for 20 years (conditions apply)

APPLICATION

A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat, smokeless fuels.

CONSTRUCTION

The flue liner has a smooth inner liner made from 904L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 904L stainless steel and is 0.12mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a quattrolock seal.

APPROVAL

Flue Liner is approved and listed by HETAS

The Flue Liner 316L/904L Grade Multifuel (100mm / 4 inch)

The Flue Liner 316L/904L Grade Multifuel (100mm / 4 inch) :

WARRANTY

904L/316L Grade Flue Liner is warranted for 10 years (conditions apply)

APPLICATION

A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat, some smokeless fuels.

CONSTRUCTION

The flue liner has a smooth inner liner made from 904L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.12mm thick. The Flue Liner is constructed from two strips of steel and the seam is folded in three planes to give a triplelock seal.

APPROVAL

Flue Liner is approved and listed by HETAS

Flue Liner (100" 4inch) 316L Grade Multifuel

Flue Liner (100" 4inch) 316L Grade Multifuel :

Flue Liner (100" 4inch) 316L Grade Multifuel

WARRANTY

316L Grade Flue Liner is warranted for 10 years (conditions apply)

APPLICATION

A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

CONSTRUCTION

The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.12mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a quattrolock seal.

APPROVAL

Flue Liner is approved and listed by HETAS.